Showing posts with label turtle. Show all posts
Showing posts with label turtle. Show all posts

Monday, 29 August 2016

Miniature turtles

Hey guys, here are the turtles I will be using for my miniature terrarium.

I started by rolling out a ball of clay to the desired size. I inserted a head pin and cut down to size. I use a tiny bit of liquid clay just to add strength.


I pre-baked at the same temperature as the package requests, but at half the time, making the clay a little harder to be able to sculpt on. Next I added clay around the pins for the head. I inserted pre-baked black balls for the eyes, and using a needle tool, added some texture to look like leathery skin.


Then I rolled out a snake, flattened it a little, and added pieces for the front legs. I added texture using a needle tool again. Then pre-baked.


After pre-baking and while the turtles were half cool, I added a small flattened ball to the back to build up more height for the shell.


For the shell I rolled out a thin sheet of clay and cut out a shape to match my turtles. I textured with a tooth brush then added scales with a fine ball tool. I also make tiny creases on each scale with a needle tool then pre-baked.


After pre-baking and once the turtles were cool, I added a small snake to the bottom to fill out the flattened areas as a result of baking on a flat surface. This is purely optional. Then you guessed it...bake again  =) This time for the full amount of time as per the recommended time.


Once the turtles have baked and cooled completely i began to add colour using citadel model paint. It's basically just fancy and expensive acrylic paint haha. However it should minimise color seepage.to resin.


Using yellow  I bled the watered down acrylic paint into the creases and then shaded each scale with burnt sienna. Then going over the edges of each scale with a darker shade. They kind of look like a leopard!


Using the same technique I shaded in the feet and head. I chose to make my turtles a little darker because they will be encased in resin.

Hope you enjoy =)

Turtle terrarium

Hey everyone! I have been working on a miniature turtle terrarium for a friend. She is a little mad for turtles =)


I decided to make this project 6 cm (2.3 in) x 4 cm (1.5 in). I started by rolling out a sheet of old polymer clay. Any color is fine as it will be covered up. I did a full bake and let it cool. Using some thick and flexible packaging that I had, I cut a single sheet for the back at 6 cm (2.3 in) x 4.5 cm (1.7 in) high, and a longer strip to cover the front and two sizes. I bent the plastic into shape using a small blow torch. Then using poly cement I assembled it as in the photo below.


Using a match that i split into two pieces I added them to the back to hide the join of the glass. For the inside I decided to go with items I found in my local hobby store, Townsville Hobbies. You can check out their google page here. I started by mixing together tacky glue and the fine sand to make a thin layer along the bottom, making sure to fill the edges, acting as a sealer for when I use resin later.


Once that set I added a thicker layer of my sand mixture to one side, I added a few super dry twigs that I found in my garden. If the twigs were green that can affect the clarity of the resin when I add that later.


Using a couple of sprigs of the lichen i carefully attached them to the hardening glue using a needle tool. I also added some 'grass' which is actually just fibers that I pulled from a coarse brush and trimmed to size.


Finally I added some card stock to the bottom rim just to hide the seams.


There are a lot of finger prints on the glass but that will disappear before I add the resin. I'm letting this dry for a full 2 days before I add any resin.

The resin I used was Diggers industrial casting resin, however any kind of resin you have on hand will be adequate. I mixed the resin as instructed and slowly dripped it in using a paddle pop stick. Just enough to cover 1 mm or 0.3 in of above the sand. I let that tack and added the turtles. I put a few drops of resin under the turtles to reduce bubbles from forming before I put them in. Once the turtles were in the position I wanted I slowly filled the remainder of the resin just to the tips of the turtle's noses. While the resin was still wet, I used a toothpick to create waves to simulate water movement.

Once the resin was dry after 24 hours, I went on to make a lid. I used a piece of base wood I painted black to match the base. I carved out a little slot to fit two hinged I found at a craft store.


Using a strip of the same card stock I used for the base, I glued it to the edges of the lid, leaving enough edge to fold over. I also attached the tiny hinges.


Card stock folded over on the top of the lid only, the bottom side will remain as it is.


Once the lid was completely dry, I attached it to the terrarium using poly cement glue.

Now my turtle haven is complete!


Hope you enjoy =)